[ Zhonghua Wardrobe ] Customized wardrobes are made of solid wood laminates, wood-plastic louvers, particleboards, and MDF. The selection criteria for the plates are to see the cut surface of the sample, look for the environmentally friendly plates, look at the quality of the veneers, and see the work of the plates.
1, solid wood laminate
The solid wood multi-layer board is made of three-layer or multi-layer veneer or thin board through high-temperature and high-pressure board glue. It is a multi-layer plywood with vertical and horizontal staggered as the base material, supplemented with polymer glue, and the surface is made of high quality solid wood. Leather or technical wood is made of fabric, which is made by several processes such as cold pressing, hot pressing, sanding and curing. The solid wood multi-layer board is pressed with uniform plywood, with small deformation, high strength, good internal quality and smoothness. Good degree, and can produce 5-40mm layers of different thickness according to requirements.
2, wood plastic louver
Wood plastic louver has waterproof, anti-mildew, anti-insect, antibacterial, acid and alkali resistant, cleanable, environmentally friendly, formaldehyde-free, not easy to deform, no cracking and flame retardant and self-extinguishing from fire. The surface of the wood-plastic louver is good in smoothness, no obvious defects, and the texture is obviously stronger than the MDF.
3, particle board
Intermediate long wood fiber + fine wood fiber on both sides, pressed into a board. Particleboard: Take the plantation, the trunk of the natural forest, the shaving of the branches or the shavings, formed by high temperature and high pressure. The advantage is that the expansion rate is small and the stability is strong. Suitable for relatively humid environments such as kitchens. The disadvantage is that it cannot be surface-milled.
4, MDF
The wood is broken, the original fiber is pressed by high temperature, the surface is flat, the milling is easy, the stability is good, and the nail holding power is strong (because the MDF is a solid material, all nail holding power is greater than the particle board). Etc. It is better than particleboard in strength and hardness. But there are also shortcomings that are not resistant to blisters.
The four major criteria for board selection:
1, different grades, plates are also different
How to judge the plate of the custom closet? Generally, look at the cut surface of the sample. From the cut surface, the blockboard is two or four layers of veneers (also thickened using four or more veneers) close to the solid wood core. The quality of the blockboard has a flat cut surface with no gaps; the MDF is made of fine fibers, and the combination is relatively tight and the weight is relatively large; the particle board is a wooden granular structure, but the combination is not tight enough and the weight is light. The poor quality can even be seen with small pores; the multi-layer board is made of a plurality of veneers, usually three or five layers.
2, look for environmentally friendly sheet
Professional custom wardrobe manufacturers use environmentally friendly panels that meet national testing standards, while some manufacturers use inferior panels that have no test reports and pose a potential threat to human health.
3, sheet veneer to see the quality
Some wardrobes look good on the surface, however, with a light stroke, you can draw obvious scratches. These custom-made wardrobes are made of surface-coated vellum paper or ornate paper sheets that are often used in low-cost wardrobes on the market, and have poor wear resistance.
4, sheet edge sealing to see work
Professional custom-made wardrobe manufacturers use precision panel saws to cut sheets, and there is no chipping around the sheets. After the edges are sealed, the water in the air is effectively prevented from intruding into the interior of the board. Some manufacturers have no professional equipment, rough cutting, and obvious edge collapse around them. Some even cut corners and only cut one side of the front side of the board. The unsealed surface easily absorbs moisture from the air, causing the sheet to swell, causing the wardrobe to deform and affecting the service life.
Frozen Meat Breaker And Grinder
Frozen meat breaker/frozen meat breaker/meat grinder/meat mincer is the first step of high quality products production. They are used for pre-breaking frozen meat blocks stacked on pallets. It includes bone saw series, frozen meat cutting machine, frozen meat flaker,grinder series, etc. Customers will use different machines depending on the processing needs and to form an automatic production line. No need of defrosting of the meat, Helper`s breaker series has been designed to cut off a whole block of meat in meat pieces with a blades system, avoiding second time pollution and keeping meat texture.
Large frozen meat breaker series: Bone saw, Frozen meat cutting machine, frozen meat flaker.
Frozen meat grinder series: JR-120, JR-140, JR-300, chopping and grinding combination system.
Rib Chopping Machine,Frozen Meat Flaker,Frozen Meat Cutter,Meat Mincer,Meat Grinder,Frozen Meat Breaker
Helper Machinery Group Co., Ltd. , https://www.helperfoodtek.com